Doosan DX340LC hydraulic Excavator Anti-swing Gear Disassembly Instructions

 This article describes the Doosan DX340LC hydraulic excavator anti-sway gear removal instructions


Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality




REMOVAL


1. Park on firm and level ground.

2. Lower front attachment (bucket) to ground.

3. Shut down engine.

4. Set safety lever on "RELEASED" position.

5. Turn starter switch to "I" (ON) position.
2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software





WARNING!


If engine must be running while performing maintenance, always use extreme caution. Always have one person in cab at all times. Never leave cab with engine running.


6. Fully stroke work levers (joysticks) in all directions to

relieve any pressure from accumulators.

7. Set safety lever on "LOCK" position.

8. Turn key to "O" (OFF) position and remove from starter

switch.

9. Hang a maintenance warning tag on controls.

10. Disconnect negative (-) battery cable leading to frame from battery.

11. Tag and disconnect hoses from swing motor (1, Figure 3). Plug and cap hoses and ports to prevent contamination

from entering hydraulic system or component.

12. Disconnect tube (2) from drain cock (3) and hose fitting (7) from fill hole.

13. Remove twelve bolts and washers (4, Figure 3) holding swing reduction gearbox (5) to frame.

14. Using a suitable lifting device, slingswing motor (1, Figure3) and remove swing motor and reduction gearbox (5) as  an assembly from unit.

 2020 Doosan Daewoo Excavator Operation and Repair Manual PDF


 
NOTE: A drain cock (3, Figure 3) and tube are on side of gearbox. Be careful not to damage valve or tube.



NOTE: There are two alignment pins (6, Figure 3), one on each side of reduction gearbox flange.

评论

发表评论

此博客中的热门博文

How to Replace Doosan DA-30-5 Truck Filter

图片
  This article mainly introduces how to replace the Doosan DA-30-5 truck filter   2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software NOTE ： Avoid spillage and   use a su itable container.   Used fuel   must be disposed of as speciied   in   nationaI   and   inter-   national   law   1. Unscrew   the   fi lter   cover   with   a   closed   tool   with   hexagon driver , e.g. socket , so   as   not   to   damage   the   fi lter   cover . 2. Lift   out   the   fi lter   cover   and   fi lter   element .   The   fi lter   housing will drain automatically.   This applies only   if the fuel   tank   is lower than the engine. Otherwise th e fuel shut-off cock must   be   closed   fi rst . Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   3. Undo   the   removed   fi lter   element   from   the   cover   by carefully bending   it to   one   side. 4. Renew   the   O - ring   in   the   cover . Lubricate   the   O - ring   with   Oring grease. 5. Check   that   the   fi
阅读全文

How to Solve the Problem of Intermittent Alarm and Speed limit of 1400RPM When the DX60-9C Excavator Engine is Working

图片
  This article mainly introduces how to solve the problem of intermittent alarm and speed limit of 1400RPM when the DX60-9C excavator engine is working.   2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software     1) Check the instrument panel fault code to display E001382-31C engine speed limit 140ORPM. ;       2) Query the meaning of the code through the fault code table: fuel filter element pressure sensor  identification error;       3) Check the voltage value of the three wires of the fuel filter element pressure sensor. Under normal  conditions, it should be: 0.85W4.9V/0.85L OV/0.85GR 2.3V when normal, when the engine alarms ov.       4) By comparing with the new car, we found that the 0.85GR line should always be around 2.4V, but  when the fault code appears on this car, it is always OV, so it is suspected that the terminal is short- circuited to ground.     Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality       After investigation, it was found tha
阅读全文

How to Solve the Walking Failure of Doosan DH220-V Excavator

图片
   This article mainly introduces how to solve the walking fault of Doosan DH220-V excavator   Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   When the machine is walking in a straight line, the right joystick remains unchanged and the left side  returns to the neutral position (i.e., stops). At this time, the right crawler continues to walk, while the  left crawler slides 800-1000mm before stopping.     1. Checking essentials:   1. After analyzing the hydraulic system, the fault Joints and motors, etc.       02. Measure the system pressure. When the boom is raised to the maximum limit so that the pressure  reaches the maximum, the measured system pressure is 330 BAR, indicating that there is no problem  with the pump.     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016   3. Apply external braking to the walking system. It was also observed that the front pump pressure was  10.5BAR, while the rear pump pressure was 270BAR.       4. After replac
阅读全文