Doosan G2 Engine Fuel System Troubleshooting Guide

 Injector Static Test Instructions

 

Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality

 Test Instructions Tools: G2-SCAN testing software, hoses, and measuring cup Purpose: 

To determine the injector backflow rate with the engine off. 

Test Conditions

 - Key switch: ON position 

- Coolant temperature: -10 to 100°C 

- Fuel temperature: -10 to 100°C 

- Battery voltage: Above 7V

Test Method: After assembling the hoses and measuring cup to the return line, use the G2SCAN software's injector static test function to perform the test. 

 

Doosan Dms-5 Diagnostic Software with Troubleshooting v3.2.7 (07.2025)

 

 


Test Results & Standards 

 


   Results: If the return flow rate is greater than the above values, the injector needs to be replaced.

 Test Results & Standards

 

评论

发表评论

此博客中的热门博文

How to solve the problem of alarm and speed limit of 1400RPM during operation of DL series engines

  How to solve the problem of alarm and speed limit of 1400RPM during operation of DL series engines     Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   Model: DL series engine  Fault phenomenon: An alarm appears during engine operation and the speed is limited to 1400RPM.   Inspection method:   1) The vehicle has been in operation for 2200 hours, the equipment speed limit is 1400rpm, and the fault code retrieved is P1251: Fuel balance leakage       2) Check the low pressure oil circuit pressure, 70kpa, which is low (normal is about 90kpa); after cleaning the oil-water separator, the low pressure increased, but the fault still occurred from time to time.   3) After the low-voltage check, the high-voltage system was tested, and the software was connected to perform cylinder disconnection test and crankshaft acceleration test. There was no obvious abnormality in the working status of each cylinder; Doosan Dms-5 D...
阅读全文

How to deal with the problem that the oil-water Separator Alarm Keeps Popping Up After the DX215-9C Doosan Construction Machinery Model is Powered on, the Engine Accelerates Normally, and the buzzer keeps sounding.

图片
  This article mainly introduces how to deal with the problem that the oil-water separator alarm keeps popping up after the DX215-9C Doosan Construction Machinery model is powered on, the engine accelerates normally, and the buzzer keeps sounding.       2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software   Inspection Method:       1) Check that the oil-water separator filter element is not clogged, and the fault persists after draining    the water;       2) The fault will disappear intermittently due to vibration during driving;         3) Check the voltage of the water level sensor and find that when there is a fault, the sensor S terminal    0.85YB line has always been an abnormal ground signal. This terminal should be 3.0-3.8V when there    is no water;     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016     4) The fault persists after ...
阅读全文

How to Ignite the Fuel System Assisted Start of DoosanDX340LC Crawler Excavator Engine

图片
This article introduces how to ignite the fuel system to assist in starting when the DoosanDX340LC Crawler Excavator engine does not start. 2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software If engine does not start, the fuel system may need priming. Prime the fuel system using the following procedure: 1. Stop Engine. 2. Open left side door and then there is fuel filter. Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality 3. Loosen plug (1, Figure 21 ) on top of fuel filter head. 4. Pump hand operated primer pump (2, Figure 21 ) by the fuel injection pump. Pump primer until fuel is present at plug hole in fuel filter head. 5. Tighten plug in fuel filter head. 6. Continue to pump primer pump until a strong resistance is felt. 7. Start engine and look for signs of leaks. Repeat procedure if necessary.
阅读全文