How to replace the DL300-3/DL350-3 wheel loader valve stem seal and valve seat

 This article explains how to replace the DL300-3/DL350-3 wheel loader valve stem seal and valve seat

 2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software

Replacing a Valve Stem Seal

1.  Remove  valve  according  to  the  work  description  for Removing valves.

2.   Remove valve stem seal with a pair of pliers.

3.   Install the valve.

 


  4.   Carefully tap a new valve stem seal into place using tool 99 323 and a hammer.

 

 


Replacing the Valve Seats

1.          Remove valve seat inserts with an expanding sleeve from the kit with puller 587270 (1,Figure 22).

NOTE:      Insert,    for    example,    an    aluminum    sheet

between the cylinder head and counterhold to protect against damage.

WARNING

AVOID DEATH OR SERIOUS INJURY

Wear protective goggles for eye protection from flying metal parts.

 


 Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016




2.  Press in new valve seat inserts.Use drift 99384(2,Figure

22)and shank 99385.Cool the drift and valve seat insert

to about -80°℃ with dry ice or liquid air.Pressing must be

done rapidly.

 

 


Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality

评论

发表评论

此博客中的热门博文

Doosan DX340LC-5 excavatorSwing Reduction Gear Removal.

图片
  This article introduces the disassembly of Doosan DX340LC-5 excavator swing reduction gear 1.       Park   on   firm   and   level   ground . 2.       Lower   front   attachment   ( bucket ) to   ground . 3.        Shut   down   engine . 4.        Set   safety   lever   on   " RELEASED " position . Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   5.       Turn   starter   switch   to   "I"   ( ON )   position .      WARNING! If      engine      must      be      running      while       performing   maintenance,    always    use    extreme  ...
阅读全文

DoosanDX340LC Crawler Excavator Cabin Installation Guide

图片
this article mainly introduces the  installation of the doosanDX340LC crawler excavator cabin 2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software 1. Using a suitable lifting device, attach slings to four lift points on top of cabin (Figure 7). NOTE: Cabin weighs approximately 290 kg (639 lb). 2. Lower cabin into position on cabin floor. 3. Install four mounting nuts on four corners of cabin floor (2, Figure 9). NOTE: Mounting nut torque 20.2 kg•m (146 ft lb) 4. Install four hex bolts (3, Figure 9) in door side of cabin floor. 5. Install two hex bolts (1, Figure 9) in right side of cabin floor and one bolt (4) in front of cabin floor. Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality Quantity Description 4 16 mm hex nuts at each corner of the cabin. 4 10 mm x 1.5 hex bolts at the door side of the cabin. 3 10 mm x 1.5 mm hex head bolts, 2 on the right side of the cabin and 1 under the front window. 6. Once cabin is mounted to floor, unhook lifting device...
阅读全文

How to deal with the problem that the oil-water Separator Alarm Keeps Popping Up After the DX215-9C Doosan Construction Machinery Model is Powered on, the Engine Accelerates Normally, and the buzzer keeps sounding.

图片
  This article mainly introduces how to deal with the problem that the oil-water separator alarm keeps popping up after the DX215-9C Doosan Construction Machinery model is powered on, the engine accelerates normally, and the buzzer keeps sounding.       2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software   Inspection Method:       1) Check that the oil-water separator filter element is not clogged, and the fault persists after draining    the water;       2) The fault will disappear intermittently due to vibration during driving;         3) Check the voltage of the water level sensor and find that when there is a fault, the sensor S terminal    0.85YB line has always been an abnormal ground signal. This terminal should be 3.0-3.8V when there    is no water;     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016     4) The fault persists after ...
阅读全文