DoosanDX340LC Crawler Excavator Cabin Disassembly Guide

this article mainly introduces the dismantling of the doosanDX340LC crawler excavator cabin

Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality
DoosanDX340LC

CAUTION!
Avoid disassembling cabin if there are strong wind gusts,
which could catch large surface area of cabin shell and
push it sideways during lift.
1. Park on firm and level ground.

2. Lower front attachment (bucket) to ground.


3. Shut down engine.


4. Set safety lever on "RELEASED" position.


5. Turn starter switch to "I" (ON) position.






WARNING!
If engine must be run while performing maintenance, use extreme care. Always have one person in the cabin at all times. Never leave the cabin with the engine running.


6. Fully stroke work levers (joysticks) in all directions to


relieve pressure from accumulators.


7. Set safety lever on "LOCK" position.


8. Turn key to "O" (OFF) position and remove from starter
switch.


9. Hang maintenance warning tag on controls.

10. Disconnect the battery cable from the negative (-) battery
terminal.


11. Prepare cabin shell for removal by disconnecting wiring
connectors for:

A. Cabin interior lighting.
B. External light wiring.
C. Radio antenna and connections.
D. Wiper/washer connections.

NOTE: Control console wiring harnesses and hydraulic
piping lines that pass through the floor of the
cabin do not need to be disassembled.
NOTE: If unit is equipped with a cabin protective
structure (for forestry, or hazardous working
conditions), it must be removed
2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software

12. Remove floor mat.

13. Remove operator's seat (1, Figure 2).

NOTE: Be careful not to damage seat covering.

14. Remove duct covers (2, 3 and 4, Figure 2). When removing cover (2) disconnect hour meter connector and cigar lighter connector. Disconnect main harness connector before removing cover (4).







15. Remove pocket (5, Figure 2) before removing side panel (6, Figure 2).


16. Remove air duct (1, 2 and 3, Figure 3) at right side of

cabin. Disconnect duct wiring connector before removing

duct (2).
17. Disconnect washer hose at floor plate bottom.








Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016

 
18. Remove cover (5, Figure 4) on left side dash cover (3) and bolts (1, Figure 5).

NOTE: When removing cover, disconnect speaker wire.

19. Remove two rubber stops (2, Figure 4) used in storing the front lower glass. Remove bolts (1) from the rear left and right dash covers. Remove left side cover (3).

20. Lift right side dash cover (4, Figure 4) and disconnect speaker wire. Remove cover.





21. Remove three bolts (2, Figure 5) after disconnecting the

speaker and antenna wires. Remove stereo assembly.



22. Disconnect cabin light wiring connector.

23. Disconnect cabin ground cable (7, Figure 2).




24. Remove four mounting nuts from four corners of cabin floor

(2, Figure 6).


25. Remove four hex bolts (3, Figure 6) from door side of cabin

floor.

26. Remove two hex bolts (1, Figure 6) from right side of cabin

floor and one bolt (4) from front of cabin floor.






27. Using a suitable lifting device, attach slings to four lift

points on top of cabin (Figure 7).

NOTE: Cabin weighs approximately 290 kg (639 lb).

28. Lift cabin approximately 25 - 50 mm (1" - 2") above deck.

Check that all electrical connections have been

disconnected and all other items unbolted.

29. Continue lifting with the assist crane to remove the cabin

shell. Lower the shell to a prepared safe blocking support.








评论

发表评论

此博客中的热门博文

DOOSAN 400 Series SKID STEER LOADER Engine Oil Filter Replacement Guidance

图片
   How to Remove/ Replace DOOSAN  440 Plus，460 Series，470 Plus SKID STEER LOADER Engine Oil Filter 1， Draining Engine Oil Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality Remove the four bolts from the access plate locat- ed on the left bottom corner of the  chassis. Remove the drain plug by either reaching through the opening between the  radiator and the chassis or through the access plate. Drain oil into an approved waste  oil receptacle. Inspect drain plug gasket and if serviceable, replace drain plug. If gasket is deformed or torn, replace gasket and re-install drain plug. Discard oil in  accordance with local environmental rules and regulations. 2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software 2 Remove/ Replace Engine Oil Filter Raise and secure operators cab. Filter is located on left side of engine block. Using a strap type or other style filter wrench, remove the engine oil filter. Before  installing
阅读全文

How to Solve the Problem of no Movement of Doosan Excavator

图片
  This article introduces how to solve the problem of no movement of Doosan excavator.   Note: All models (except S55-V) After the engine is started, press the safety lever on the left console and operate the left and right handles. The whole vehicle will not move.       Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016    1. Checking essentials     a. Check that 6# fuse is not burned out, it is normal.     b. When it is infinity, it is normal when it is closed and it is 0.   c resistance is 13.5 ohms normal.     d. Check that the valve core of the work cut-off solenoid valve is functioning normally. After e was  disassembled, it was found that the spring in the relief valve was broken.     2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software 2. Reason:  The spring in the relief valve is broken, causing the pilot pressure to be too low, unable to push the valve  core to move, and the enti
阅读全文

How to Replace Doosan DA-30-5 Truck Filter

图片
  This article mainly introduces how to replace the Doosan DA-30-5 truck filter   2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software NOTE ： Avoid spillage and   use a su itable container.   Used fuel   must be disposed of as speciied   in   nationaI   and   inter-   national   law   1. Unscrew   the   fi lter   cover   with   a   closed   tool   with   hexagon driver , e.g. socket , so   as   not   to   damage   the   fi lter   cover . 2. Lift   out   the   fi lter   cover   and   fi lter   element .   The   fi lter   housing will drain automatically.   This applies only   if the fuel   tank   is lower than the engine. Otherwise th e fuel shut-off cock must   be   closed   fi rst . Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   3. Undo   the   removed   fi lter   element   from   the   cover   by carefully bending   it to   one   side. 4. Renew   the   O - ring   in   the   cover . Lubricate   the   O - ring   with   Oring grease. 5. Check   that   the   fi
阅读全文