DOOSAN 400 Series SKID STEER LOADER Engine Oil Filter Replacement Guidance

   How to Remove/ Replace DOOSAN  440 Plus，460 Series，470 Plus SKID STEER LOADER Engine Oil Filter
1， Draining Engine Oil
Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality
Remove the four bolts from the access plate locat- ed on the left bottom corner of the

 chassis. Remove the drain plug by either reaching through the opening between the 

radiator and the chassis or through the access plate. Drain oil into an approved waste 

oil receptacle. Inspect drain plug gasket and if serviceable, replace drain plug.

If gasket is deformed or torn, replace gasket and re-install drain plug. Discard oil in 

accordance with local environmental rules and regulations.




2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software



2 Remove/ Replace Engine Oil Filter

Raise and secure operators cab.

Filter is located on left side of engine block.

Using a strap type or other style filter wrench, remove the engine oil filter. Before 

installing new filter, coat the rubber gasket on the filter with clean oil.

Install filter BY HAND and tighten until gasket

fully contacts the mounting surface.

Tighten 1/2 to 3/4 of a turn, by hand only.





Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016


评论

发表评论

此博客中的热门博文

DoosanDX340LC Crawler Excavator Fuel Tank Installation Guide

图片
This article describes how to install the DoosanDX340LC crawler excavator oil tank Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality 1. Install two 12 mm eyebolts in threaded holes (38 and 39, Figure 13). Using a      suitable lifting device, sling eyebolts. 2. Set fuel tank (1, Figure 13) into position. Install six bolts (8) and spacers (13) finger tight, to secure tank to frame. NOTE: The clear level gauge on the side of the tank is easily damaged. Be careful of obstacles and wind gusts. 3. Install shims (9, Figure 13) as needed to prevent tank (1) from rocking or stress from mounting bolts (8). 4. Tighten mounting bolts (8, Figure 13) after shims are installed. NOTE: Bolt torque is 27 kg•m (200 ft lb). 5. Connect wires as tagged to fuel sender (2, Figure 14) on side of fuel tank (1). 6. Install four bolts (33, Figure 15 ) and battery cover (34) on frame.Install two bolts (31) and brac...
阅读全文

DoosanDX340LC Crawler Excavator Cabin Installation Guide

图片
this article mainly introduces the  installation of the doosanDX340LC crawler excavator cabin 2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software 1. Using a suitable lifting device, attach slings to four lift points on top of cabin (Figure 7). NOTE: Cabin weighs approximately 290 kg (639 lb). 2. Lower cabin into position on cabin floor. 3. Install four mounting nuts on four corners of cabin floor (2, Figure 9). NOTE: Mounting nut torque 20.2 kg•m (146 ft lb) 4. Install four hex bolts (3, Figure 9) in door side of cabin floor. 5. Install two hex bolts (1, Figure 9) in right side of cabin floor and one bolt (4) in front of cabin floor. Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality Quantity Description 4 16 mm hex nuts at each corner of the cabin. 4 10 mm x 1.5 hex bolts at the door side of the cabin. 3 10 mm x 1.5 mm hex head bolts, 2 on the right side of the cabin and 1 under the front window. 6. Once cabin is mounted to floor, unhook lifting device...
阅读全文

How to deal with the problem that the oil-water Separator Alarm Keeps Popping Up After the DX215-9C Doosan Construction Machinery Model is Powered on, the Engine Accelerates Normally, and the buzzer keeps sounding.

图片
  This article mainly introduces how to deal with the problem that the oil-water separator alarm keeps popping up after the DX215-9C Doosan Construction Machinery model is powered on, the engine accelerates normally, and the buzzer keeps sounding.       2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software   Inspection Method:       1) Check that the oil-water separator filter element is not clogged, and the fault persists after draining    the water;       2) The fault will disappear intermittently due to vibration during driving;         3) Check the voltage of the water level sensor and find that when there is a fault, the sensor S terminal    0.85YB line has always been an abnormal ground signal. This terminal should be 3.0-3.8V when there    is no water;     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016     4) The fault persists after ...
阅读全文