How to install and remove SCANIA DC13 series engines

This article mainly introduces how to install and remove SCANIA DC13 series engines

    

Note: Doosan DX420LC-9C/DX500LC-9C is scania DC13 engine.(Authorized by Doosan Corporation）

step 

 1Remove - Generator 1 on the engine, use the battery main switch or disconnect the battery terminals to cut off the power supply. 

 2. Clean the area if necessary. You may also need to remove the base plate, etc. to facilitate access.

  3. Remove the load from the belt drive. See the "Timing gear" chapter. 

 4. Disconnect positive lead 30 and control lead. 5. Remove the alternator. 

 09.2023 Scania SDP3 (Diagnostic & Programmer)Truck and Bus 2.58.1

 

 

 

 

  INSTALLATION - GENERATOR ON ENGINE NOTE: Inspect the multi-groove V-belt/belt with belt

 tensioner and idler pulley for wear or damage. Replace if necessary. 

 1. Install the alternator. 

 2. Install positive lead 30 and control lead.  

3. Install the belt drive. See the "Timing gear" chapter.  

4. Install fenders, hatch covers, etc. 

 5. Turn on the battery main switch or connect the wires to the battery terminals. examine

 Scania SDP3 Marine Industry Diagnostic Software 2.49.3



   terminals. examine

 Note: Do not operate the alternator without disconnecting the battery! This may cause the rectifier 

and/or voltage regulator to be overloaded or destroyed.

NOTE: To obtain correct results, the alternator should be maintained at a temperature of 20-25°C.

  Higher temperatures may result in lower current flow.

When the engine control unit generates a fault code for the alternator, the following tests can be 

performed.

Output test

Control voltage test

Stage measurement brush length

Slip rings, rotor resistance and overshoot  

 11.2023 Scania Multi 2310 EPC Parts Catalog & Service Manuals Installation Service

 

评论

发表评论

此博客中的热门博文

How to Replace Doosan DA-30-5 Truck Filter

图片
  This article mainly introduces how to replace the Doosan DA-30-5 truck filter   2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software NOTE ： Avoid spillage and   use a su itable container.   Used fuel   must be disposed of as speciied   in   nationaI   and   inter-   national   law   1. Unscrew   the   fi lter   cover   with   a   closed   tool   with   hexagon driver , e.g. socket , so   as   not   to   damage   the   fi lter   cover . 2. Lift   out   the   fi lter   cover   and   fi lter   element .   The   fi lter   housing will drain automatically.   This applies only   if the fuel   tank   is lower than the engine. Otherwise th e fuel shut-off cock must   be   closed   fi rst . Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   3. ...
阅读全文

How to Solve the Problem of Intermittent Alarm and Speed limit of 1400RPM When the DX60-9C Excavator Engine is Working

图片
  This article mainly introduces how to solve the problem of intermittent alarm and speed limit of 1400RPM when the DX60-9C excavator engine is working.   2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software     1) Check the instrument panel fault code to display E001382-31C engine speed limit 140ORPM. ;       2) Query the meaning of the code through the fault code table: fuel filter element pressure sensor  identification error;       3) Check the voltage value of the three wires of the fuel filter element pressure sensor. Under normal  conditions, it should be: 0.85W4.9V/0.85L OV/0.85GR 2.3V when normal, when the engine alarms ov.       4) By comparing with the new car, we found that the 0.85GR line should always be around 2.4V, but  when the fault code appears on this car, it is always OV, so it is suspected that the terminal is short- circuited to ground.     Doosan Diagnostic Too...
阅读全文

How to Solve the Walking Failure of Doosan DH220-V Excavator

图片
   This article mainly introduces how to solve the walking fault of Doosan DH220-V excavator   Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   When the machine is walking in a straight line, the right joystick remains unchanged and the left side  returns to the neutral position (i.e., stops). At this time, the right crawler continues to walk, while the  left crawler slides 800-1000mm before stopping.     1. Checking essentials:   1. After analyzing the hydraulic system, the fault Joints and motors, etc.       02. Measure the system pressure. When the boom is raised to the maximum limit so that the pressure  reaches the maximum, the measured system pressure is 330 BAR, indicating that there is no problem  with the pump.     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016   3. Apply external braking to the walking system. It was also observed that the front pump p...
阅读全文