How to Replace Doosan DA-30-5 Truck Filter

 This article mainly introduces how to replace the Doosan DA-30-5 truck filter

 2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software

NOTE：

Avoid spillage and use a suitable container. Used fuel  must be disposed of as speciied in nationaI and inter- national law

 


1. Unscrew the filter cover with a closed tool with hexagon driver, e.g. socket, so as not to damage the filter cover.

2. Lift out the filter cover and filter element. The filter housing will drain automatically. This applies only if the fuel tank is

lower than the engine. Otherwise the fuel shut-off cock

must be closed first.

Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality 

3. Undo the removed filter element from the cover by

carefully bending it to one side.

4. Renew the O-ring in the cover. Lubricate the O-ring with Oring grease.

5. Check that the filter housing is drained of fuel.

Contaminated fuel may enter the injectors if the drainage does not work.

6. Press a new filter element into the snap fastener in the cover.

7. Fit the filter element and cover in the filter housing. Tighten

the cover to 25 Nm (18.4 lbf.ft).

8. Bleed the fuel system after renewing the water separating

filter.

 Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016

评论

发表评论

此博客中的热门博文

How to solve the problem of alarm and speed limit of 1400RPM during operation of DL series engines

  How to solve the problem of alarm and speed limit of 1400RPM during operation of DL series engines     Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   Model: DL series engine  Fault phenomenon: An alarm appears during engine operation and the speed is limited to 1400RPM.   Inspection method:   1) The vehicle has been in operation for 2200 hours, the equipment speed limit is 1400rpm, and the fault code retrieved is P1251: Fuel balance leakage       2) Check the low pressure oil circuit pressure, 70kpa, which is low (normal is about 90kpa); after cleaning the oil-water separator, the low pressure increased, but the fault still occurred from time to time.   3) After the low-voltage check, the high-voltage system was tested, and the software was connected to perform cylinder disconnection test and crankshaft acceleration test. There was no obvious abnormality in the working status of each cylinder; Doosan Dms-5 D...
阅读全文

Doosan G2 Engine Fuel System Troubleshooting Guide

图片
 Injector Static Test Instructions   Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   Test Instructions Tools: G2-SCAN testing software, hoses, and measuring cup Purpose:  To determine the injector backflow rate with the engine off.  Test Conditions  - Key switch: ON position  - Coolant temperature: -10 to 100°C  - Fuel temperature: -10 to 100°C  - Battery voltage: Above 7V Test Method: After assembling the hoses and measuring cup to the return line, use the G2SCAN software's injector static test function to perform the test.     Doosan Dms-5 Diagnostic Software with Troubleshooting v3.2.7 (07.2025)     Test Results & Standards       Results: If the return flow rate is greater than the above values, the injector needs to be replaced.   Test Results & Standards  
阅读全文

How to deal with the problem that the oil-water Separator Alarm Keeps Popping Up After the DX215-9C Doosan Construction Machinery Model is Powered on, the Engine Accelerates Normally, and the buzzer keeps sounding.

图片
  This article mainly introduces how to deal with the problem that the oil-water separator alarm keeps popping up after the DX215-9C Doosan Construction Machinery model is powered on, the engine accelerates normally, and the buzzer keeps sounding.       2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software   Inspection Method:       1) Check that the oil-water separator filter element is not clogged, and the fault persists after draining    the water;       2) The fault will disappear intermittently due to vibration during driving;         3) Check the voltage of the water level sensor and find that when there is a fault, the sensor S terminal    0.85YB line has always been an abnormal ground signal. This terminal should be 3.0-3.8V when there    is no water;     Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016     4) The fault persists after ...
阅读全文