How to Changing The Doosan DA-30-5 Truck Water Separating Fuel Flter

This article explains how to replace the Doosan DA-30-5 truck water separation fuel filter

 Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality

1. Close the shut-off cock (1) in the fuel pipe and

position a container under the filter.

2. Open the drain tap (2) in the filter cover and let

the fluid run down into the container.

3. Unscrew the filter cover.

4. Unscrew the filter from the filter head.

5. Discard the old filter and use a new filter.

6. Lubricate the O-ring in the filter cover with engine oil.

  2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software


 

7. Screw the filter cover onto the new filter by hand. Make sure that the drain tap is fully closed.

8. Lubricate the O-ring on the filter with engine oil.

9. Fill the width of the filter with clean fuel.

10. Screw the filter into position until the O-ring rests against the filter head. Tighten the filter another 1/2-3/4 turn by

hand.

11. Open the shut-off cock and check the system for leaks.

12. Bleed the fuel system.

Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016 

 

评论

发表评论

此博客中的热门博文

How to solve the problem of alarm and speed limit of 1400RPM during operation of DL series engines

  How to solve the problem of alarm and speed limit of 1400RPM during operation of DL series engines     Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   Model: DL series engine  Fault phenomenon: An alarm appears during engine operation and the speed is limited to 1400RPM.   Inspection method:   1) The vehicle has been in operation for 2200 hours, the equipment speed limit is 1400rpm, and the fault code retrieved is P1251: Fuel balance leakage       2) Check the low pressure oil circuit pressure, 70kpa, which is low (normal is about 90kpa); after cleaning the oil-water separator, the low pressure increased, but the fault still occurred from time to time.   3) After the low-voltage check, the high-voltage system was tested, and the software was connected to perform cylinder disconnection test and crankshaft acceleration test. There was no obvious abnormality in the working status of each cylinder; Doosan Dms-5 D...
阅读全文

Doosan G2 Engine Fuel System Troubleshooting Guide

图片
 Injector Static Test Instructions   Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality   Test Instructions Tools: G2-SCAN testing software, hoses, and measuring cup Purpose:  To determine the injector backflow rate with the engine off.  Test Conditions  - Key switch: ON position  - Coolant temperature: -10 to 100°C  - Fuel temperature: -10 to 100°C  - Battery voltage: Above 7V Test Method: After assembling the hoses and measuring cup to the return line, use the G2SCAN software's injector static test function to perform the test.     Doosan Dms-5 Diagnostic Software with Troubleshooting v3.2.7 (07.2025)     Test Results & Standards       Results: If the return flow rate is greater than the above values, the injector needs to be replaced.   Test Results & Standards  
阅读全文

How to Disassemble and Disassemble a Doosan Engine Starter Motor

图片
  This article explains how to disassemble and disassemble a doosan engine starter motor           Doosan Diagnostic Tool UVIM Support Doosan Excavators High Quality 1. Disconnect the negative (-) cable of the battery first   . 2. Remove the wires from the electromagnetic switch assembly.     3. Remove the mounting bolts of the starter motor (Figure 2, (1)). Remove the starter motor from the flywheel housing.       Disassembly of starter motor 1. Loosen the M8 nut on the electromagnetic switch (solenoid) (Figure 3). Disconnect the wires from the solenoid switch.   2023.07 Doosan DMS-5 Data Monitoring System Diagnostic Software  2. Remove the two M4 bolts (Figure 4, (1)). These two bolts are used to lock the rear end cover (Figure, (2)) and the carbon brush holder assembly. (image 3)).     3. Remove the two M5 through-bolts (Figure 4, (4)). Separate the rear end cover (Fig. 4, (2)), field coil (Fig. 4,...
阅读全文